Dented, bent or cracked garage door panel? Asmara Garage Door Repair Edmonton replaces damaged garage door panels with a matching section, and we tell you straight when a new door is the better deal. We check the hinges, rollers and track around the damage and rebalance the door. The service call is free, and every panel we install comes with a 3-year warranty.
Asmara Garage Door Repair Edmonton repairs and replaces garage door panels across Edmonton. Asmara technicians check the whole door first, then match the new section to your door's maker, model, size and colour. When more than one section is damaged, we price a new door too, so you pick the better deal. You get a free service call and the exact price before any work starts. In Edmonton, panels get dented by cars sliding on icy driveways, pucks off the driveway hockey net, and doors closing on something left underneath.
Clear Pricing
The service call is free, and you get the exact price before any work starts. These are the prices we charge across Edmonton.
| Repair description | Cost (+ GST) | What's included |
|---|---|---|
| Dented or damaged panel, 16 ft | $1,000–$1,500 | Panel, supplied and installed |
A garage door is built from 4 or 5 horizontal sections, called panels, joined by hinges. Damage to one panel changes how the whole door runs.
A small dent in the face of a panel is a looks problem. If the door runs smooth and seals at the floor, it doesnt need a new panel.
A fold across the panel, or a bent edge where two panels meet, weakens the section. The door binds, rubs or wont close flat.
Water gets into a crack, freezes and opens it wider through the winter.
The opener pulls on the top panel. A weak spring or a sticking door bends the top section near the opener arm.
The bottom panel sits in salt, slush and meltwater all winter. Rust or rot along the bottom edge means that section is done.
A steel garage door panel has foam behind it, so a dent doesnt pull out like a car door. Some damage gets repaired and some gets a new section. Not sure which? Book a garage door repair visit and we check the whole door.
Yes, when the door maker still makes your panel. We order it by maker, model, size and colour so it lines up with the rest of the door. Older or discontinued doors have no matching panel, and then a new door is the fix.
One 16 ft panel costs $1,000–$1,500 + GST, and a new door costs $1,500–$2,500 + GST, installed. When two or more sections are damaged, or the door is old, a new door is the better buy. We price both and you compare them side by side.
The bottom panel takes the hits from cars, salt and slush. It holds the bottom brackets and the floor seal, so we refit both when it gets replaced.
The top panel holds the opener bracket, and opener makers recommend a steel strut across it. A missing strut is why top panels bend. We check for one on every top panel job, and because a strut adds weight, we recheck the spring balance after.
A hit in the middle of the door means taking the door apart down to that section. We reset every hinge and roller on the way back up.
Our panel price covers one 16 ft wide section, the size on a double-car door, supplied and installed.
A new panel has to match your door's maker, model, width, height, colour and insulation, or it sticks out. Look for the makers sticker on the inside of the door, and send us a photo when you call.
We work on Steel-Craft, Garaga, Amarr, Clopay and Wayne Dalton doors, plus most builder-grade doors in Edmonton.
A dent in a steel panel with foam behind it doesnt pull out clean. Filler from a repair kit hides it, but the patch shows through the paint. Tightening a loose hinge screw with the door closed is fine. Leave the bottom panel to us, because its brackets hold the lift cables under spring tension.
We look at the damaged panel, the hinges, rollers and track around it, and the door balance.
We take the maker, model, size and colour, and order the matching section.
We secure the door, take it apart down to the damaged section, and install the new panel with its hinges and rollers.
We rebalance the door, check the seal at the floor, and run it until it travels straight and closes flat.
Word for word from our Google reviews.
Excellent on Google
The photos show the extent of the damage to my garage door. Two people told me I had to replace the entire door. Emmanuel carefully inspected it and fixed everything by himself in just a couple of hours. His work was excellent, his price was very reasonable, and he saved me a lot of money. Honest, humble, and highly skilled. I highly recommend Emmanuel to anyone in need of garage door repairs.
Read moreImmanuel did a great job repairing our garage door. The strut was broken, and the door was not working properly. He was very patient, explained everything clearly, and took the time to solve the problem. He was professional and knowledgeable, and we really appreciated his excellent service. Highly recommend!
Read moreReplacing one dented or damaged 16 ft wide panel costs $1,000–$1,500 + GST, supplied and installed. A new door costs $1,500–$2,500 + GST. The service call is free and you get the exact price before we start. See panel replacement prices.
Yes, when the damage is a small dent, a bent hinge, a broken strut or a loose end cap. A creased, cracked or rusted-through panel gets replaced.
Yes, when the maker still makes a matching panel for your door. If it doesnt, a new door is the fix.
Panels come from the door maker, matched to the model, size and colour. Putting one in means taking the door apart under spring tension, so its a job for a technician.
One panel, when only one is damaged and a match exists. With two or more bad sections, the panels add up to as much as a new door or more. We price both.
Yes. We repair and replace damaged sections on commercial overhead doors.
Yes. Panels we supply and install come with our 3-year parts and installation warranty.
A hit that bends a panel bends other parts too. These are the parts we check on every panel call.
A hit hard enough to bend a panel knocks rollers out of the track.
Rollers on a damaged section get bent or cracked. We swap them with the panel.
When two or more sections are damaged, a new door is the better buy. We price both.
A bent bottom panel breaks the floor seal. We refit the seal so snow stays out.
